AmetekHaydonKerk AmetekAMS

36000 36mm

36000 Series Haydon Rotary Can Stack Stepper Motor
Haydon's can stack rotary stepper motors are built to provide exceptionally high torque to size ratios.  The Haydon 36000 can stack rotary stepper motor is 36mm rotary stepper motor with a holding torque of up to 4.5oz-in(3.18Ncm).  Typical applications include medical equipment, bar code scanning devices, printing equipment, laboratory instrumentation and other high torque, small space mechanisms.
  • Specifications - Bipolar +


    Part Number 36440-05 36440-12 36540-05 36540-12
    Wiring Units  Bipolar
    Step Angle  Degree 7.5° 15°
    Winding Voltage  VDC 5 12 5 12
    Current / Phase  A rms 0.46 0.19 0.46 0.19
    Resistance / Phase  ohms (Ω) 11 63 11 63
    Inductance / Phase  mH 7.2 45 5.5 35
    Holding Torque  oz-in (Ncm) 4.5 (3.18) 2.9 (2.05)
    Detent Torque  oz-in (Ncm) .28 (.20) .37 (.26)
    Power consumption  Watts 4.6
    Rotor Inertia  gcm2 10.5
    Weight  oz  (g) 2.5 (70)
    Insulation resistance  MΩ 20
    Insulation Class   Class B (75°C Rise)
    Standard motors are Class B rated for a maximum temperature of 130°C
  • Specifications - Unipolar +


    Part Number   36460-05 36460-12 36560-05 36560-12
    Wiring  Units  Unipolar
    Step Angle  Degree 7.5° 15°
    Winding Voltage  VDC 5 12 5 12
    Current / Phase  A rms 0.46 0.19 0.46 0.19
    Resistance / Phase  ohms (Ω) 11 63 11 63
    Inductance / Phase  mH 3.8 19 3 15
    Holding Torque  oz-in (Ncm) 3.0 (2.12) 2.0 (1.41)
    Detent Torque  oz-in (Ncm) .28 (.20) .37 (.26)
    Power consumption  Watts 4.6
    Rotor Inertia  gcm2 10.5
    Weight  oz  (g) 2.5(70)
    Insulation resistance  MΩ 20
    Insulation Class   Class B (75°C Rise)
    Standard motors are Class B rated for a maximum temperature of 130°C
  • Dimensional Drawing +


     Sleeve Bearing Motor
      36mm Can-Stack Rotary Sleeve Bearing Motor Dimensional Drawing
     Ball Bearing Motor
      36mm Can-Stack Rotary Ball Bearing Motor Dimensional Drawing
  • Performance Curves +


    TORQUE vs. PULSE RATE
    L/R Drive, Bipolar, 7.5° Step Angle

    36mm Can-Stack Rotary Motor Performance Curve
    TORQUE vs. PULSE RATE
    L/R Drive, Bipolar, 15° Step Angle
    36mm Can-Stack Rotary Motor Performance Curve

    TORQUE vs. PULSE RATE
    L/R Drive, Unipolar, 7.5° Step Angle
    36mm Can-Stack Rotary Motor Performance Curve

    TORQUE vs. PULSE RATE
    L/R Drive, Unipolar, 15° Step Angle
    36mm Can-Stack Rotary Motor Performance Curve

    TORQUE vs. PULSE RATE
    Chopper Drive, Bipolar 7.5° Step Angle
    36mm Can-Stack Rotary Motor Performance Curve

    TORQUE vs. PULSE RATE
    Chopper Drive, Bipolar, 15° Step Angle
    36mm Can-Stack Rotary Motor Performance Curve


    NOTE:  All chopper drive curves were created with a 5 volt motor and a 40 volt power supply.

    Ramping can increase the performance of a motor either by increasing the top speed or getting a heavier load accelerated up to speed faster.  Also, deceleration can be used to stop the motor without overshoot.

    With L/R drives peak force and speeds are reduced, using a unipolar drive will yield a further 30% force reduction.

    25% Duty Cycle is obtained by a special winding or by running a standard motor at double the rated current.

  • Wiring Diagram and Stepping Sequence +



    wiring diagram

    Stepping Sequence - Can-Stack Stepper Motors


    rotation-lft Bipolar Q2-Q3 Q1-Q4 Q6-Q7 Q5-Q8 rotation-rt
    Unipolar Q1 Q2 Q3 Q4
    Step        
    1 ON OFF ON OFF
    2 OFF ON ON OFF
    3 OFF ON OFF ON
    4 ON OFF OFF ON
    1 ON OFF ON OFF
  • Part Number Guide +




    36

    5

    4

    0

    -

    12

    -

    000

    Prefix

    Series Number
    Designation

    Style

    Coils

    Code ID
    Resolution Travel/Step


    Voltage


    Suffix

    (Include only when using the following)

    T=High Temperature

    R=Rare Earth Magnet

    36=36000 (Series numbers
    represent approximate width of motor body)

    4=7.5°
    5=15°

    4=Bipolar
    (4 wire)

    6=Unipolar (6 wire)



    0=Rotary Motor


    05=5 VDC
    12=12VDC
    Custom V available


    999=Ball Bearings
    001=Ball Bearings for Z Series Rotary Stepper Motors
    000=Sleeve Bearings

    XXX=Proprietary suffix assigned to a specific customer application. The identifier can apply to either a standard or custom part.


    NOTE: Dashes must be included in Part Number (–) as shown above. For assistance call our Engineering Team at 203 756 7441.