AmetekHaydonKerk AmetekAMS
USA
Search

AC Synchronous

Size 17 Stepper Motor Linear Actuator
Stepping motors can also be run on AC (Alternating Current).  However, one phase must be energized through a properly selected capacitor.  In this case the motor is limited to only one synchronous speed.  For instance, if 60 hertz is being supplied, there are 120 reversals or alterations of the power source.  The phase being energized by a capacitor is also producing the same number of alterations at an offset time sequence.  The motor is really being energized at the equivalent of 240 steps per second.

  • Specifications +


    Series
    		 Size Watts AMPS Capacitor
    (Mfd)
    @ 60 Hz
    		 Capacitor
    (Mfd)
    @ 50 Hz
    		 Coil Resistance
    (Ohms)
    		 Connection
    Diagram

    		          Main Wind.
    		 Cap. Wind
    		  
    35000
    		 14 5.7 0.21 15 15 300 300 3
    43000
    		 17
    		 6.5 0.27 15 15 104 104 3
    57000 23 13.0 0.60 30 40 35 35 3
    87000* 34 30.0 2.00 200 200 2.3 2.3 4

    ** With 12 OHM, 100 watt resistor in series


  • Wiring Diagram +



    Wiring Diagram AC Synchronous Linear Actuator

  • Part Number Guide +



    A

    35

    H

    4

    N

    -

    24

    -

    800

    Prefix

    Series Number
    Designation

    Style

    Coils

    35000 and 43000 Series Code ID
    Resolution Travel/Step

    57000 Series Code ID Resolution Travel/Step

    87000 Series Code ID Resolution Travel/Step

    Voltage


    Suffix

    A=A Coil

    35=35000 (Size 14)
    43    =43000 (Size 17)
    57    =57000 (Size 23)
    87    =87000 (Size 34)

    F=1.8° Non-captive
    H    =1.8° Captive or External (use “E” or “K” Prefix for External version)

    4=Bipolar
    (4 wire)

    N=.00012-in (.0030)
    K    =.00024-in (.0060)
    J    =.00048-in (.0121)
    Q    =.00096-in (.0243)
    P    =.00015625-in (.0039)
    A    =.0003125-in (.0079)
    B    =.000625-in (.0158)
    C    =.00125-in (.0317)
    R    =.00192-in (.0478)

    High Resolution

    U=.00006-in (.0015)
    V    =.000078-in (.00198)

    7=.000125-in (.0031)
    S    =.0004167-in (.01058418)
    3    =.0005-in (.0127)
    1    =.001-in (.0254)
    A    =.0003125-in (.0079)
    T    =.0008333-in (.0211)
    2    =.002-in (.0508)

    High Resolution

    P=.00015625-in (.003969)
    X    =.00020833-in (.00529166)
    9    =.00025-in (.0635)

    3=.0005-in (.0127)
    B    =.000625-in (.0158)
    C    =.00125-in (.0317)
    Y    =.0025-in (.0635)
    Z    =.005-in (.127)

    24=24 VDC

    800=External Linear (added to Captive shaft part number)

    XXX=Proprietary suffix assigned to a specific customer application. The identifier can apply to either a standard or custom part.



    NOTE: Dashes must be included in Part Number (–) as shown above. For assistance call our Engineering Team at 203 756 7441.